Can I Set Up A Bathtub Myself?
Can I Set Up A Bathtub Myself?
Blog Article
Here in the next paragraph yow will discover a lot of brilliant insight concerning How to Install a Bathtub.
Setting up a bath tub isn't exactly rocket science, however it does call for solid plumbing, carpentry, and also sometimes, tiling skills. Replacing an old bath tub with a brand-new one is also a moderately tough task. If the old bathtub is readily accessible, the project can move immediately; if you need to open up a wall to eliminate the old tub as well as place the brand-new bathtub, the task is much harder. In either situation, the job is within a residence handyman's abilities, although you will need an assistant to move out the old tub and set in the new one. Make certain you have actually certified yourself for the task as well as fit trying it. As opposed to working with a service provider to take over a halfway-completed project, it is better to consider utilizing one before you begin. Possibilities are you may need an expert plumber to make tube connections.
This article will help you install a new bathtub in your bathroom if you have already bought a brand-new bathtub and also do not require to transform the setup of your previous water pipelines.
Your devices as well as product checklist ought to comprise the following:
Getting ready for the Setup
Firstly, the supporting structure provided with the bathroom ought to be fitted (if required) according to the manufacturer's guidelines. Next off, fit the faucets or mixer to the tub. When fitting the faucet block, it is necessary to make certain that if the tap features a plastic washer, it is fitted between the bathroom and also the faucets. On a plastic bath, it is also reasonable to fit a sustaining plate under the faucets device to avoid strain on the bathtub.
Fit the adaptable faucet connectors to the bottom of both faucets utilizing 2 nuts and also olives (often supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and after that pass the outlet via the hole in the bathroom. Make use of the nut supplied by the manufacturer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bath. Make sure you utilize all of the provided washers.
Attach the trap to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Attach the bottom of the overflow tube in a comparable manner.The bathroom should currently be ready to be suited its final placement.
Removing Old Taps
If you need to change old taps with brand-new ones as a part of your installation, after that the first thing you should do is detach the water supply. After doing so, switch on the faucets to drain any type of water continuing to be in the system. The process of eliminating the existing taps can be rather problematic because of the restricted gain access to that is often the situation.
Make use of a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that attaches the supply pipes to the taps. Have a fabric all set for the remaining water that will certainly originate from the pipes. When the supply pipelines have been eliminated, make use of the same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to stop the solitary faucets from turning during this process. As soon as the taps have been eliminated, the holes in the bath/basin will certainly need to be cleaned of any type of old securing substance.
Before carrying on to fit the new faucets, contrast the pipe connections on the old faucets to the brand-new taps. If the old taps are longer than the brand-new faucets, then a shank adapter is required for the new faucets to fit.
Setting up the Tub
Utilizing both wood boards under its feet, place the bathtub in the required position. The wooden boards are useful in evenly spreading the weight of the bathtub over the location of the boards rather than focusing all the weight onto four small points.
The following objective is to ensure that the tub is leveled all round. This can be accomplished by examining the spirit level and changing the feet on the bathtub until the spirit level reads degree.
To set up faucets, fit all-time low of the outermost adaptable tap connector to the appropriate supply pipe by making a compression join; after that do the same for the other tap.
Turn on the water as well as check all joints and new pipework for leaks and tighten them if required. Fill up the tub and likewise inspect the overflow outlet as well as the normal outlet for leakages.
Finally, fix the bath paneling as defined in the supplier's user's manual. Tiling as well as securing around the tub must wait up until the bathtub has been utilized a minimum of once as this will settle it into its last placement.
Suitable New Touches
If the tails of the new taps are plastic, then you will require a plastic adapter to avoid damage to the string. One end of the port fits on the plastic tail of the tap and the various other end supplies a connection to the current supply pipelines.
If you need to fit a monobloc, after that you will need decreasing couplers, which attaches the 10mm pipeline of the monobloc to the basic 15mm supply pipe.
Next off, position the faucet in the mounting opening in the bath/basin making sure that the washers remain in location in between the tap and the sink. Safeguard the faucet in place with the manufacturer given backnut. As soon as the faucet is safely in place, the supply pipelines can be linked to the tails of the taps. The faucets can either be attached by using corrugated copper piping or with regular faucet connectors. The previous kind needs to be linked to the tap finishes first, tightening just by hand. The supply pipes can later be attached to the other end. Tighten both ends with a spanner after both ends have actually been connected.
Tiling Around the Bath tub
In the area where the bathroom satisfies the tile, it is needed to seal the accompanies a silicone rubber caulking. This is very important as the fitting can move sufficient to crack a stiff seal, creating the water to permeate the wall in between the bath and also the tiling, resulting in difficulties with dampness as well as feasible leaks to the ceiling listed below.
You can choose from a range of coloured sealers to blend in your components as well as installations. They are sold in tubes as well as cartridges, and also are capable of securing voids as much as a size of 3mm (1/8 inch). If you have a bigger space to load, you can load it with twists of soaked newspaper or soft rope. Bear in mind to always fill up the bath tub with water before securing, to allow for the motion experienced when the bathtub is in use. The sealer can fracture fairly early if you do not think about this activity before sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are likewise conveniently offered on the marketplace. It is suggested to fit the tiles utilizing waterproof or waterproof adhesive and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a passionate person who reads about How to Install a Bathtub, I figured sharing that article post was beneficial. Be sure to take the opportunity to promote this blog entry if you enjoyed reading it. I recognize the value of reading our article about A Step-by-Step Guide to Installing a Bathtub.
Click For More Information
Report this page